Traffic Light Control System

Traffic Light Control System
Details:
Traffic light control systems are widely used to monitor and control the flow of automobiles through the junction of many roads. The master and slave controller are both have dual-band wireless module.
Send Inquiry
Description
Send Inquiry

1,Introduction

Traffic light control systems are widely used to monitor and control the flow of automobiles through the junction of many roads. The master and slave controller are both have dual-band wireless module. It enhances the anti-jamming. Each master controller/salve controller has 11 outputs channels maximum (4 control phases). The communication distance can reach 600m between master controller and slave controllers, junctions less than 600m can be controlled by one master controller. The master controller adopts same frequency interference measuring ability, it can monitor if the same frequency interference signal exists or not. The master controller and slave controller have auto-degrading function while in serial communication failure, and auto-recovery function when the communication is on while in degrading state.


2. Advantages

Traffic Light Control System applies LED lamps with die-casting aluminum shell, ensuring  efficient signaling on the junction. This product is designed to make sure that traffic and pedestrians move as smoothly, and safely as possible. This wireless control system has enhanced on its outdoor performance, and it can work between minus 40 degrees and 70 degrees which will barely malfunction. Also it can save option scheme for 10 years maximum when power off, so this is also a convenient choice to be treated as a temporary replacement system.


3,Specification

Parameters of Traffic Light Control System

Traffic Light Control System

Communication Mode of Hosts and Auxiliary

Wireless or RS485 Cable

Wireless Communication Frequency

490MHZ

Wireless Communication Baud Rate

9600bps

Wireless Transmit Power

≤100mw

Wireless Communication Distance

>600m

Time and Sequence of Motor Light Runs

All Red (can be set)→Green→ Green Flashing(can be set)→Yellow→ Red

Resistance to Surge Current for Each Output

≥100A

Working Temperature

-40°C~ 70°C

Working Condition Relative Humidity

<95%

Save option scheme(when power off)

10 years


Parameters of LED Lamp

LED Lamp

Lamp Diameter

φ200mm/φ300mm/φ400mm

Working Power Supply

170V ~ 260V 50Hz

Rated Power

φ300mm<10w/φ400mm<20w

Light Source Life

>50000 hours

Working temperature

-40°C~ +70°C

Relative Humidity

≤95%

Reliability

MTBF≥10000 hours

Maintainability

MTTR≤0.5 hours

IP Rating

IP65

Color

Red/green/yellow

Material

Aluminum die casting


Parameters of Light Pole

Light Pole


Product name

Durable Double Arm / Single Arm Signal Traffic Light Pole LED Stop Lights Pole

Shape

Conoid , Multi-pyramidal, Columniform, polygonal or conical

Material

Usually Q345B/A572,minimum yield strength>=345n/mm2
Q235B/A36,minimum yield strength>=235n/mm2
As well as Hot rolled coil from Q460 ,ASTM573 GR65, GR50 ,SS400, SS490, to ST52

Surface treatment

Hot dip galvanized Following ASTM A 123, color polyester power or any other standard by client required.

Wind Speed

160 Km/Hour

Minimum yield strength

350mpa

Minimum ultimate tensile strength

490mpa

Max ultimate tensile strength

620mpa

Standard

ISO 9001

Length of per section

Within 14m once forming without slip joint


Parameters of Anchor Bolt

Anchor Bolt


Material

Q235 Steel

Bolts and Nuts Material

Stainless Steel

Galvanizing

Cold dip galvanized process ( optional )

Features

Detachable, helping to save transport space and cost


4,Feature and Application

Traffic Light Control System is easy to connect wire Inside the cabinet, there are all kinds of sign of connection in each channel. you just need to open terminal block and put the thread into the cabinet and tighten the screw, then the installation will be finished.

In addition, Our products offer security and reliability. The front and the back of the cabinet are locked with locks. When you do not need it, you can lock it up; as well as has a high level of waterproof function, the side of the cabinet is installed with waterproof cotton, has a very good waterproof effect, in addition, our Traffic Light Control System have remote management function, you can remotely perform tasks such as forced flash, close the intersection and download plans.

Feature and Application of Traffic Light Control System


5, DetailsDetails of Traffic Light Control System


6, Production Process

Production Process of Traffic Light Control System


7,Packaging and Shipping

Packaging and Shipping of Traffic Light Control System


8,FAQ

Q1. Are you a factory or a trading company?

A:We are a factory and we have a professional research and development team of skilled workers and technician.

Q2. What about the lead time?

A: Sample needs 5-7 days, mass production time usually needs 2-3weeks.

Q3. What is your terms of payment ?

A: Usually we accept T/T, irrevocable L/C at sight. For regular orders, Terms of payment 30% deposit, full payment before delivery the goods.

Q4. How to proceed an order?

A: Firstly, let us know your requirements or application.

Secondly, we quote according to your requirements or our suggestions.

Thirdly, customer confirms the samples and places deposit for formal order.

Fourthly, we arrange the production and delivery.

Q5. Is OEM or ODM acceptable?

A :Yes, both OEM and ODM are acceptable.


Product certification

Hot Tags: traffic light control system, China traffic light control system manufacturers, suppliers, factory

Send Inquiry